Tel : +86 15333853330 (eward)

Email : [email protected]

AISI 4140 Alloy Steel (UNS G41400) - AZoM.com

AISI 4140 alloy steel is annealed at 872°C (1600°F) followed by slowly cooling in the furnace. Tempering. AISI 4140 alloy steel can be tempered at 205 to 649°C (400 to 1200°F) depending upon the desired hardness level. The hardness of the steel can be increased if it has a lower tempering temperature.

Heat Treating 4140 steel FAQ : anvilfire.com How-to.

3) Tempering recommendations from the ASM heat treaters guide for 4140-4142 is a minimum of 400°F. This leaves near full hardness. The following table is extrapolated from a hardness graph given in Brinell Hardness with nearest points taken from a conversion table for Rockwell hardness. Tensile values are generic, not specifically for 4140.

Hardness of Heat Treated 4140 - Metal and Metallurgy ...

Hardness of Heat Treated 4140 by swall. ... unless the actual alloy content is on the high side of the spec range or a water quench is used instead of oil. These hardness values are for as-quenched material and final hardness will need to be reduced by tempering before the part can be put into use.

4140 Alloy Steel Data Sheet

4140 Alloy Steel Data Sheet. 4140 is an alloy steel that is supplied in either the annealed or prehardened condition. The prehardened condition is heat treated to a medium hardness (HRC 28/32) and is designated as 4140 HT. 4140 annealed is supplied in the soft condition and can be hardened to RC 54. 4140 annealed is designated as 4140 Ann or simply 4140. 4140 HT is supplied in many forms such ...

15 Common Applications for Versatile 4140 Steel - Otai ...

AISI 4140 steel grade is a versatile steel grade. 4140 material is widely used in a lots of industrial fields. It is a chromium-molybdenum alloy steel. The chromium content provides good hardness penetration, and the molybdenum content ensures uniform hardness and high strength.

ASTM 4140 Hardness Range - discount stainless steel

is there a maximum hardness level for 4140 - Metal and . is there a maximum hardness level for 4140 t2photo (Materials) (OP) Whatever the differences are, try staying out of the 450 -700° F tempering range.

AISI 4140 Chrome-Molybdenum High Tensile Steel

Yield strengths range from 110 ksi through 140 ksi, but we can temper it to other strength levels. When compared with standard 4140 heat treated to the same tensile and yield strengths, 4140HW achieves significantly higher toughness, as measured by impact strength (see Figure 9). 4140HW combines medium carbon content with high-end chromium,

4140 HIGH TENSILE STEEL - interlloy.com.au

4140 HIGH TENSILE STEEL 4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved

4140 High Tensile Steel | Interlloy | Engineering Steels ...

4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved machinability, which greatly increases feeds and/or speeds, while also extending tool life without adversley affecting mechanical properties.

4140 Steel Bar AISI A29 | 1.7225 | 42CrMo4 | SCM440 - Otai ...

7. Hardening of AISI Alloy Steel 4140. AISI alloy 4140 steel bar, plate and square can be hardened by cold working, or heating and quenching. SAE 4140 alloy steel is usually supplied ready heat treated to hardness in 18-22 HRC. If further heat treatment is required, then heat to 840 oC – 875 oC, hold until temperature is uniform throughout ...

AISI 4140 Alloy Steel - 1.7225 | SCM440 - Heat Treat ...

What is 4140 Steel? AISI 4140 steel also can be called DIN 1.7225 and JIS SCM440 steel. 4140 alloy steel has high fatigue strength and low notch sensitivity. Low-temperature impact toughness is also very high, no obvious temper brittleness. It is mainly used after quenching and tempering state.

4140 High Tensile Steel | Interlloy | Engineering Steels ...

4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved machinability, which greatly increases feeds and/or speeds, while also extending tool life without adversley affecting mechanical properties.

Heat-Treating & Hardening 4140 Steel - Material ...

Jun 30, 2006· 4140 is not case hardened by carburizing but it is frequently induction hardened to the hardness and depth you desire and beyond. If you want the core to be softer you can first normalize, or quench & temper in a furnace to the desired lower hardness level. This treatment also prepares the near surface for optimum induction hardening response.

4140 Heat Treated Steel Plate | Precision Grinding, Inc.

Standard Hardness. 4140 PH has a standard, industry recognized Rockwell C Hardness rating of 28 – 32. Most sources recognize and tend to prefer quoting and requesting the Rockwell C Scale. 4140PH ranges from Brinell Hardness 270 – 300. Thick 4140 AN (in the annealed condition) is flame cut, then annealed onsite in our furnace.

4140 Alloy Steel | 1.7225 | 42CrMo4 | 42CD4 | 2244 | S ...

4140 Steel Annealing Slowly heat to 800~8500 ºC, keep enough time, ensure heat thoroughly. then cooling in furnace to 480 ºC , then cool in air. After annealing, the hardness 92 HBS Max. AISI 4140 Steel Hardening & Quenching 4140 Steel is usually used at 18-22 HRc, If needs, AISI 4140 alloy steel can be hardened or

4140 Pre Hard - BICO Steel Service Centers

616.453.2400 / 800.962.4140 F: 616.453.2929 [email protected] BICO SOUTH, INC. Spartanburg, SC 864.574.2121 / 800.998.1025 F: 864.574.4140 [email protected] 4140 Pre Hard • 4140PH is a chromium-manganese-molybdenum grade • This grade is delivered in a prehardened condition at a hardness level of ...

Mechanical Properties & Hardness - Oliver Steel

Mechanical Properties & Hardness. Quench-and-tempering or heat treating requirements for 1045, 4140, and 4340 plate usually call out a hardness range, but it is not uncommon for an application to require certain mechanical properties beyond hardness. Normal ranges of mechanical properties corresponding to a specific hardness are listed below.

ASTM 4140 steel

Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. ASTM 4140 Round Bar ASTM 4140 Flat Bar ASTM 4140 Hollow Bar ASTM 4140 Tube / Pipe ASTM 4140 Sheet / Plate ASTM 4140 Strip / Coil ASTM 4140 Wire ASTM 4140 Forging ASTM 4140 Tube / Pipe TEL:+86-13880247006

4140 Tool Steel Grade, Shape, Size, Tech - Tool Steel ...

The prehardened condition is heated to medium hardness (HRC 26/34) plate to be used as a holder material for high strength structural components. 4140 Tool Steel Shapes and Sizes. 4140 tool steel is available in the following thickness sizes and standard width sizes depicted in the tables below.

Make Sure Your Specified Heat Treatment is Achievable B

surface hardness in oil is shown below Maximum Steel grade section size, in. 1045 0.250 5140 0.750 4140 1.5 4340 3.0 The commercially accepted range for surface hardness after tempering is 5 HRC points or 40 BHN points as shown in Table 2. Determining the expected core hardness range can be determined Carbon content, Rockwell hardness for ...

4130 and 4140 Heat Treatments - Industrial Heating

Jun 08, 2011· For 4140 steel, the recommended heat treatment [1] consists of heating to austenitizing temperature, typically 1570°F (855°C), followed by oil quenching. Tempering (reheating after quenching) will achieve the desired hardness range.

Speedy Metals Information for 4140 Annealed Cold Roll Steel

The chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength. Through variations in the method of heat treating 4140, an exceptionally wide range of properties can be attained.

4140 Steel Plate | Precision Grinding, Inc.

Purchased as rolled, Pre-Hardened (PH) or in the annealed condition, 4140 steel plate possesses a full range of hardening and wear resistance properties. Due to it’s good hardness penetration and uniformity, flame hardening, induction hardening, or oil hardening can increase the wear resistance of 4140 …

34611 | 4140/4142H | 4140 | ALLOY | Metals | Castle Metals ...

Alloy 4140 (AISI 4140) is one of the most popular direct hardening Cr-Mo alloy steel plates that have the ability to develop an extensive range of hardness and strength. Alloying elements and thermal treatments, such as quenching and tempering, greatly influence the hardness and strength of the steel.

AISI 4140 Alloy Steel - 1.7225 | SCM440 - Heat Treat ...

What is 4140 Steel? AISI 4140 steel also can be called DIN 1.7225 and JIS SCM440 steel. 4140 alloy steel has high fatigue strength and low notch sensitivity. Low-temperature impact toughness is also very high, no obvious temper brittleness. It is mainly used after quenching and tempering state.

ASTM 4140 Steel | 1.7225 | 42CrMo4 | SCM440 - OTAI Special ...

ASTM 4140 Steel is a Alloy Structural Steel belong to ASTM A29/A29M Steel Grade standard. AISI 4140 used in Oil and Gas industry and Large Machinery Strutural. 4140 Steel China Supplier and factory Otai Special Steel Supply ASTM 4140 steel in Round bar, Plate, …

4140 or 41L40 for heat treat - Practical Machinist

Feb 16, 2013· Have a print calls for 40-42 RC finished hardness. Material available is 4140 prehard at 25 RC, or 41L40 annealed at 187 brinell. I realize it will rough faster in the annealed condition, and would have to be re-hardened if I used the pre-hard material. My question is whether or not the inclusion of ...

4140 Tool Steel Grade, Shape, Size, Tech - Tool Steel ...

The prehardened condition is heated to medium hardness (HRC 26/34) plate to be used as a holder material for high strength structural components. 4140 Tool Steel Shapes and Sizes. 4140 tool steel is available in the following thickness sizes and standard width sizes depicted in the tables below.

AISI 4140 - Howco

Low alloy 4140: ASTM A29 (VO1.05) General scope. AISI 4140 low alloy steel containing Chromium and Molybdenum is the most widely used alloy for oil patch applications. Usually supplied in the hardened and tempered condition at 22 HRC max. it also finds favour in many applications requiring higher strength levels up to 150 KSI 0.2% PS.

4140 Steel Plate | Precision Grinding, Inc.

Purchased as rolled, Pre-Hardened (PH) or in the annealed condition, 4140 steel plate possesses a full range of hardening and wear resistance properties. Due to it’s good hardness penetration and uniformity, flame hardening, induction hardening, or oil hardening can increase the wear resistance of 4140 …

AISI / SAE 4140 Alloy Steel - AISI 4140 Forgings | All ...

The nominal normalizing temperature for 4140 grade is 1600 º F (870 º C), but production experience may necessitate a temperature either 50 º F (10 º C) above or below this figure. In fact when forgings are normalized before, say, carburizing or hardening and tempering, the upper range of normalizing temperatures is used.

How To Weld 4140 Steel | WELDING ANSWERS

L et’s keep it simple. 4140 steel can be welded without problems as long as you follow some simple guidelines. This also applies to AISI 4140 and 4340. We will not be discussing the metallurgical properties of 4140 or trying to explain what happens to its microstructure when it cools too rapidly, just remember that the key is to control our cooling rate.

AISI 4130 Steel - West Yorkshire Steel

It is supplied as round bar commonly in the hardened and tempered condition with a hardness of 18-22 HRc. With a lower carbon content range AISI 4130 provides better weldability, at the expense of through thickness strength, than that of other oil and gas steel grades such as AISI 4140 .

4140 Steel | Associated Steel Corporation

Hardness range from Rockwell “C” 38/42 to 55/62 depending upon application. This customer-manufactured component is suited to handle many applications that are found in various industries including automotive, food processing, material handling, and large manufacturing.

AISI 4140 Steel - West Yorkshire Steel

The higher carbon content of AISI 4140 gives greater strength and heat treatment capabilities in comparison to AISI 4130, however it does have inferior weldability characteristics. AISI 4140 machines well in the supply condition of 18-22HRc. We welcome export enquiries for AISI 4140 steel.

4140 Steel | 4150 Steel | B7 | Associated Steel Corporation

Hardness range from Rockwell “C” 38/42 to 55/62 depending upon application. This customer-manufactured component is suited to handle many applications that are found in various industries including automotive, food processing, material handling, and large manufacturing.

Steel Hardness Conversion Table

Steel Hardness Conversion Table. This table shows approximate hardness of steel using Brinell, Rockwell B and C and Vickers scales. These conversion charts are provided for guidance only as each scales uses different methods of measuring hardness. The right hand column show an approximate equivalent tensile strength.